Before starting the installation:
You would need the following items for a perfect installation:
- Wallpaper paste
- 1 liter of cold water
- Cuvette for the preparation of a glue
- Pencil and paper tape
- Measuring tools (ruler, tape measure …)
- Spirit level (you can replace it with a heavy
- object for example. scissors hanging on a string)
- Glue brush
- Brush and roller for wallpaper
- Utility knife
- A soft sponge or cloth
Applying the wallpaper (step by step)
Step 1: wall preparation
Prepare the selected wall. The wall surface must be clean, dry, and grease-free (best results are obtained on a wall covered with a white topcoat). Our wallpaper can help you hide small imperfections in the walls, but if the defects are deep, they should be filled before installation. If the wall is of contrasting colors, it is recommended to mask them with a bright color. Before installing the new wallpaper, please remove any previous wallpaper residue from the wall surface.
Step 2: cutting the lengths
Cut the wallpaper roll along the dotted line (marked on the back of each wallpaper roll). Unfold the strips in the correct order and check the pattern for any errors and if the strips match and fit each other. If you notice any problem, please contact us to replace the roller. Our return and exchange policy is straightforward. Satisfied or refunded with no questions asked. We offer fast and secure exchange.
Step 3: gluing the wall
Prepare the glue. When using Wow Wall Decor wallpaper paste: Mix one bag (50g) brawl in 1 liter of cold water then wait 15 minutes. After 15 minutes, stir the glue again. Now you can start the app. Very important information for the best result: The non-woven wallpaper does not need to be wet before installation, it suffices to apply the glue on the wall and then start laying the strips in the order mentioned on the back of each roll.
Step 4: glue treatment
Apply the prepared glue to the wall surface, dedicated to the first strip of a wallpaper (this may be an area slightly wider than the width of one strip). Spread a thin layer of glue using a brush. Make sure that the glue layer is not too thick and that it is unitary. Do not apply glue to the wallpaper. Take the first strip of wallpaper. Make sure where the top is and that you are starting from the correct roll. Ride starting
from below (with the pattern inside) or simply fold it back gently to avoid dirtying the surface of a wallpaper
Step 5: first roll
Place the upper part of the strip in the right place and at the right height on an adhesive-coated fragment of the wall. Then gently extend the strip, sticking it along the entire length. Check if the first strip is placed evenly along the designated lines. Otherwise, gently slide the strip into the correct position. Our wallpapers are perfectly matched, which means that there is no adjustment necessary to have a perfect pattern.
Step 6: finishing the roll
Using a brush, carefully smooth the surface of the wallpaper, removing any unevenness and air bubbles. Move the brush in a circular motion from the center of the width to the sides, starting at the top surface. Be careful – do not smear the brush with glue. Excess glue can be removed with a soft damp sponge or cloth. Be careful – wiping the surface of a wallpaper with a too hard sponge can destroy a print.
Step 7: repetition
Repeat these steps for the following strips of wallpaper. Please note that the edges of the pattern should be the same, excess glue can be removed with a soft damp sponge or cloth. Be careful – rub the surface of a wallpaper with a
too hard a sponge can destroy a print.
Step 8: final touches
When you finish pasting and the scratches are smoothed out with a brush, cut off any redundant parts of a wallpaper using a utility knife (including the white edges). Please make sure the knife is clean and sharp. Using a dull utility knife can damage the wallpaper.
Video of the installation of the wallpaper: ( Via Art Wallcoverings )
Some tips after installation:
A-Again make sure that the wallpaper adheres to the wall over the entire surface, that the stripes have been applied evenly, and that the pattern has not been distorted. The best assessment can be made at a distance of about 1 to 2 meters. If you notice that this pattern is out of place or out of place (recently after pasting wallpaper), you can gently move the lengths back onto a wall to line it up.
B-Using a paint roller, please smooth the surface of a wallpaper again. There may still be small air bubbles under
the wallpaper that you cannot remove, but it should disappear within one to three days
C-Remember to maintain a temperature above 10 ° C and a constant supply of air in the room, this will help you to better control the strips if there is a problem when pasting the wallpaper.
D- Don’t try to “help” the natural drying process of wallpaper. Do not use any device that could accelerate it. If possible, please avoid intense heating, especially if wallpaper has been applied near heating devices
As part of the complete transparency, we ask all our customers to send us an image or video after the installation of the wallpaper or other products offered on the site (if they wish of course), If you wish to you be inspired by customer achievements before choosing your wallpaper, please see the page by clicking on the button below. If you have already obtained one of our products and wish to send us a photo or video of your rendering, we will be honored to pose on this customer realization page.Results of our clients and influencers